New bearing for the fan.

New water inlet and replacement of solenoid valve.

Works fine otherwise

Complete renovation Replace a beam 100x40 Repacked piston plus painted up Built new bracket hydraulic pump Manufactured protection for pump Fitted adjustable feet Container dimensions: 85x109cm, height 92cm Total dimensions: 145x175cm, height 220cm

Description Year model 2005 A tool for 2 pcs 195×125 troughs 230 volt 16 amp 2000w

Only Gas

Smoke cabinet from Protech. Runs with liquid smoke

Model: FGM 20/80 F 1.1 kW

Tick rate/Speed: Adjustable needle speed, usually between 15 and 65 strokes per minute depending on product and desired injection volume

Conveyor/Bandwidth: The conveyor belt is 280 mm wide (designed for smaller meat pieces or fish fillets). The belt is driven in full synchronization with the needle stroke movement

Number of needles: 20 pieces mounted on a needle bridge (single-needle configuration).

Capacity: 100kg Tray: 60x40cm Lifting height approx: 65cm Air pressure: 6bar

Function check, everything works as it should.

Test run OK 100kg capacity jaws: 60x40cm

Repaired function lever for grinding

Manufactured/modified cutter

New springs lock 2pcs

New wheels 4 pcs lockable

New bearings and seals in the flour mill drive

New screw tapping

Capacity: Has a capacity of up to about 1,800 kg per hour, depending on the final disc used and the material's properties.

Mixing function: In addition to grinding, can also mix the mince with spices, water or other additives directly in the container before the grinding process begins.

Flexible control: Foot pedal for easy hands-free operation, but can also be controlled via the regular control panel

Work safety: Equipped with the necessary safety switches and emergency stop, making it approved for commercial use and staff

Mixing carrier (trolley): Fits up to about 66 kg (145 lbs) of meat at a time for mixing.

Fixed the hatch New tensioner for the hatch The machine uses central vacuum and central cooling. Vacuum and cooling chamber pressure tested and are tight.

Test run and adjusted welding times

Works well

Pipe size: 156mm

Welding width: 25cm

Front end knife missing, sensor triggered

Capacity: The machine is designed to operate at speeds of up to 50 bags per minute according to the specifications, although in practice it often runs at a lower, more stable pace (around 20–30 bags/min) depending on the properties of the product.

Drive and mechanics: The construction is largely made of stainless steel to meet high hygiene requirements. The machine's weld backs and foil advance are driven by servo motors, while the other mechanical functions are controlled using pneumatics (compressed air).

Offered with or without control cabinet and transformer.

Replace front bearing

Replace p-box motor

Mesta el utbytt

Renovered tensioner

Front cover could not be repaired; lock switch.

High capacity: Engineered to withstand continuous chopping with a capacity of up to 180 animal bodies per hour.

Simple cleaning: The saw has fully opening doors and smooth surfaces in the enclosure to facilitate cleaning and maintain strict hygiene requirements.

Lubrication system: The machine is equipped with a drive system located in an oil lubrication bath, which reduces wear and minimizes downtime.

More information can be found in this (PDF):

https://neust.com.co/wp-content/uploads/2020/06/Sierra-de-Canal-JARVIS-modelo-Buster-V..pdf

Test run OK

Fully automatic stapling/placing: The machine slices the product and automatically places the slices in neat rows, stacks, or circular patterns (shingling/stacking) on a receiving table.

Material: Built in 100% robust, food-grade stainless steel for maximum hygiene and long service life.

Capacity & Precision: The machine operates with reduced return stroke which maximizes the number of discs per minute, while stepless adjustment guarantees exact disc thickness without waste.

Refurbished lifting device for cleaning. Measured and checked the condition of heating rods, 7pcs heating rods replaced with new. Power heating rods: 4500 watts x12 Dimensions: 530x150cm Belt: 60cm Internal measurement for product: 400x60cm. Adjustable belt speed.

With oil container 1100liter
Electric cartridges, thermostat and float tested, work well.

Outer dimensions: 230x110cm, height 195cm

Refurbished feed screw, new bearing bottom part plastic New seals lids and hatches Repaired band New button covers -No vibrator

Manufactured missing pressing tools

Replace a button

Corrosion-protected various interior

Welded feet.

Capacity: Depending on the product and configuration, the hydraulic press operates at an efficiency of about 6–12 cycles per minute.

Chamber & Product Size: The machine's forming tool provides a standardized product size of 300x200 mm with adjustable height.

Material: Designed in stainless steel and acid-resistant elements to meet strict hygiene requirements and withstand tough cleaning procedures in meat processing environments.

Cleaned the pump and serviced it

Works fine

Tool: 250x140mm

Capacity: Up to 3–6 cycles per minute (depends on vacuum level, gas handling and operator speed).

Maximum film width: 450 mm

Maximum tray size (1-compartment): Approximately 325 × 265 mm

New bearings front wheel.

Tensioner refurbished

Fixed hookbox

Mounted water fittings.

High capacity: It is designed for high-intensity production lines and can cut up to 400 pigs per hour (or 200 sows per hour) per saw.

Powerful motor: Equipped with a completely enclosed electric motor of 3.0 hp (2237 W), providing both reliability and protection in damp slaughter environments

Rep circuit board in frequency converter. Built brackets and fixed electrical cabinet. New feeder cable ATTENTION! After a power failure, the lift must be reset with an emergency stop. And you should drive at low speed towards the end positions. Two speeds. Works perfectly

Test run OK

Capacity: Holds 6 GN 1/1 containers.

Performance (Coolant cooling): Cool 30 kg of food from +90 °C to +3 °C core temperature in under 90 minutes.

Performance (Frost/Freezing): Freeze 25 kg of food from +90 °C to -18 °C in less than four hours.

Material: The entire inner and outer structure is made of high-quality stainless steel.

More information can be read here (PDF):

https://7daychef.com/products/specs/HDBB010.pdf?srsltid=AU7gw4UY3mBnKgTxCYPDxCPvx218xwdoXaocjhf1pZks7IcoDvlFLDTN

New band test run works Must be calibrated when installing detecttronic technician Product height Max 14cm

Test run OK

Cleaned electrical cabinet Change the main switch Switch buttons in remote control New bearings + packing box in drive shaft New bearings + packing box in engine Test driven

Change the emergency stop Review Works well Max product height 10cm

Newly painted hydraulic tank and engine Tub width: 100cm Tub depth: 75cm Lifting height: 110cm

Test run runs quietly and smoothly

Capacity: Capable of grinding about 800–950 kg per hour depending on the final disc.

Knife system: Equipped with Unger B98 system (5 parts) with a clearance wheel of 98 mm.

Trattvolym: Has a large feed hopper/bowl of 45 liters.

Power Powerful industrial motor at 2.9 kW.

Renovated outer drive unit uncoupler.

Change oil in vacuum pump.

Change oil in the gearbox.

Smort trattlagring.

Tested, no faults.

Capacity: Up to 3,000 kg/h (depends on product and application).

Fill pressure: Up to 35 bar.

Dosing speed: Up to 600 portions per minute.

Portioning interval: Between 5 g and 100,000 g.

Trattkapacitet: 240 liter (removable funnel for easy cleaning).

Test run works fine

Pipe size: 500 x 500 mm

Tank volume: 17 liter

Boiler capacity: 5.7 liters

Sound level: About 62–63 dB(A) thanks to double-wall insulation

Manual:

https://www.metos.se/o/commerce-media/accounts/-1/attachments/146982394?download=true

New air hoses, New air bellows, New Teflon tape, Changed the order of the belts, 2 new potentiometers, Changed the input air pressure regulator, New oil in the vacuum pump, New silicone strips under the welding beams, 1 new switch for emergency stop, Renovated/cleaned vacuum and pressure valve.