Replaced start, stop button and lamp. Welded and fixed the blade guide under the table. New protective ball bearing behind the blade.
Made missing press tools Change a button Rust-protected misc. Inside Welded feet.
Replaced packing boxes in the mixer gearbox Welded mixer arm Fixed bushing for mixer arm Painted engines and gearboxes
Mounted cutoff on-off Replace main power switch Renovated welding beam The machine runs with an external vacuum pump or central vacuum (pump not included, can be purchased separately) Welding beam: 80x70cm The conveyor belt is included
All buttons replaced A contactor replaced Manufacturing miscellaneous Levers, etc Test drive
Frying /Fryer/Cooking - top condition! Barely used, has been in warm storage. "With VarioCooking Center MULTIFICIENCY®, Frima VCC you can cooking, roasting, roasting, low-temperature cooking, confectionery, sous-vide cooking... without supervision, without burning, without the stress of handling pots and pans."
Painted engine compartment Renovated electrical cabinet Review light curtain, one light curtain replaced with a new one. New start and stop buttons. Installed new engine Change the gaskets in one of the mixer arms.
New shaft + bearing slave side conveyor belt. 3 new heating cartridges. New feeder cable. New door for electrical cabinet. New inlet and outlet curtains
Replace air distributor Replace welding tape Change the oil Fixed connectors for pinch protection Double weld + cut off
Replaced a position sensor for the trough holder. Replaced the phase sequence monitor. Cleaned the throttle valve for the cooling water. Repaired the locking of the door on the back. Changed the oil in the vac pump. Cleaned the air filter for the vac pump.
Test Driven New Condition! Chamber Dimensions: 320x890x100 mm Machine Dimensions: 480x1066x970 mm Welding Beam: 2x310
Renovated outer drive unit agitator. Changed oil in vac pump. Changed oil in gearbox. Lubricated funnel bearing. Test driven, among other things.
Renovated right mixer arm bearing. New sensor door switch. New blocks for air valves. Renovated air cylinders for lid lift. Made new drain plug for mixer. Runs quietly and nicely.
New main switch New buttons New limit switch mechanism New connection cable Mounted protection over chain Test run works well
New input and output bands New knife Works perfectly
Changed oil and oil filter. New locking mechanisms (x2) for the hatch to the engine compartment, 1 better used welding beam (modified), New welding wires and tape on the welding beams, New connectors to the welding beam New rubber seal for the lid, New screen part, Aligned the lid, Changed tires,
Test run works well Mounted pressure regulator Fixed alarm tower Band width: 20cm Product height: 10cm
All advanced control is disconnected. Slice thickness is controlled by air-pressured control
New foot pedal installed. New relay and engine protection. Otherwise very good condition.
Change the oil Replace welding tape Change silicone strip Replace lid seal Vacuum value 7
Replaced start, stop button and lamp. Welded and fixed the blade guide under the table. New protective ball bearing behind the blade.
Made missing press tools Change a button Rust-protected misc. Inside Welded feet.
Replaced packing boxes in the mixer gearbox Welded mixer arm Fixed bushing for mixer arm Painted engines and gearboxes
Mounted cutoff on-off Replace main power switch Renovated welding beam The machine runs with an external vacuum pump or central vacuum (pump not included, can be purchased separately) Welding beam: 80x70cm The conveyor belt is included
All buttons replaced A contactor replaced Manufacturing miscellaneous Levers, etc Test drive
Frying /Fryer/Cooking - top condition! Barely used, has been in warm storage. "With VarioCooking Center MULTIFICIENCY®, Frima VCC you can cooking, roasting, roasting, low-temperature cooking, confectionery, sous-vide cooking... without supervision, without burning, without the stress of handling pots and pans."
Painted engine compartment Renovated electrical cabinet Review light curtain, one light curtain replaced with a new one. New start and stop buttons. Installed new engine Change the gaskets in one of the mixer arms.
New shaft + bearing slave side conveyor belt. 3 new heating cartridges. New feeder cable. New door for electrical cabinet. New inlet and outlet curtains
Replace air distributor Replace welding tape Change the oil Fixed connectors for pinch protection Double weld + cut off
Replaced a position sensor for the trough holder. Replaced the phase sequence monitor. Cleaned the throttle valve for the cooling water. Repaired the locking of the door on the back. Changed the oil in the vac pump. Cleaned the air filter for the vac pump.
Test Driven New Condition! Chamber Dimensions: 320x890x100 mm Machine Dimensions: 480x1066x970 mm Welding Beam: 2x310
Renovated outer drive unit agitator. Changed oil in vac pump. Changed oil in gearbox. Lubricated funnel bearing. Test driven, among other things.
Renovated right mixer arm bearing. New sensor door switch. New blocks for air valves. Renovated air cylinders for lid lift. Made new drain plug for mixer. Runs quietly and nicely.
New main switch New buttons New limit switch mechanism New connection cable Mounted protection over chain Test run works well
New input and output bands New knife Works perfectly
Changed oil and oil filter. New locking mechanisms (x2) for the hatch to the engine compartment, 1 better used welding beam (modified), New welding wires and tape on the welding beams, New connectors to the welding beam New rubber seal for the lid, New screen part, Aligned the lid, Changed tires,
Test run works well Mounted pressure regulator Fixed alarm tower Band width: 20cm Product height: 10cm
All advanced control is disconnected. Slice thickness is controlled by air-pressured control
New foot pedal installed. New relay and engine protection. Otherwise very good condition.
Change the oil Replace welding tape Change silicone strip Replace lid seal Vacuum value 7